 |
|
Specifications |
|
| |
Input |
 |
Input Voltage |
|
90-264 VAC (120-370 VDC) |
|
Input Frequency |
|
47-63 Hz |
|
Input Current |
|
120 W: 1.7 / 1.0 A at 115 / 230 VAC
150 W: 2.0 / 0.8 A at 115 / 230 VAC
180 W: 2.7 A at 90 VAC |
|
Inrush Current |
|
120 W: 20 / 51 A at 115 / 230 VAC
150 W: 54 / 63 A at 115 / 230 VAC
180 W: 54 / 108 A at 115 / 230 VAC
|
|
Power Factor |
|
EN61000-3-2 class A
120 W: EN61000-3-2 class C for loads ≥30%
150 W: EN61000-3-2 class C n/a
180 W: EN61000-3-2 class C for loads ≥50% |
|
Earth Leakage Current |
|
120 W: 0.30 / 0.75 mA at 115 / 230 VAC
150 W: 0.40 / 0.75 mA at 115 / 230 VAC
150 W (medical): 0.075 mA at 230 VAC
180 W: 0.75 mA at 230 VAC
|
|
Input Protection |
|
Internal T3.15 A / 250 VAC fuse |
|
No Load Input Power |
|
180 W: ≤ 0.5 W |
| |
Output |
|
Output Voltage |
|
See datasheet |
|
Output Voltage Trim |
|
±5% output 1 only (3.3 V variant ±10%)
SDS180: not user adjustable |
|
Initial Set Accuracy |
|
Single output models: ±1%
Multi-output models: ±5% |
|
Minimum Load |
|
No minimum load required for single output models. For multi-output models see table. |
|
Start Up Delay |
|
2 s max |
|
Start Up Rise Time |
|
2 ms typical |
|
Hold Up Time |
|
16 ms minimum at full load and 110 VAC |
|
Line Regulation |
|
0.5% typical |
|
Load Regulation |
|
3.0% typical |
|
Transient Response |
|
4% max deviation, recovery to within 1% in 500 µs for a 50% load change
|
|
Ripple & Noise |
|
1% pk-pk typical, 20 MHz bandwidth |
|
Overvoltage Protection |
|
112-132% V1 only, recycle input to reset
|
|
Overload Protection |
|
All outputs: 110-150% with auto recovery
(primary power limit)
|
|
Short Circuit Protection |
|
Trip & restart (Hiccup mode), auto recovery |
|
Temperature Coefficient |
|
±0.04%/°C |
| |
General |
|
Efficiency |
|
120 W: 80% typical
150 W and 180 W: 88% typical |
|
Isolation |
|
3000 VAC Input to Output
1500 VAC Input to Ground
500 VAC Output to Ground
SDS150-M: 5600 VDC Input to Output
2800 VDC Input to Ground
500 VDC Output to Ground |
|
Switching Frequency |
|
120 W: PFC 100 kHz typical,
PWM 67 kHz typical
150 W: PFC 34 kHz minimum,
PWM 55 kHz typical
180 W: PFC 67 kHz typical,
PWM 67 kHz typical |
|
Power Density |
|
120 W: 4.87 W/In3, 150 W: 6.50 W/In3
180 W: 7.47 W/In3 |
|
Signals |
|
Power Fail Detect = TTL active low,
combined AC and DC OK signal (option)
Warning time 16 ms
|
|
MTBF |
|
>100 kHrs to MIL-HDBK-217F at 25 ºC, GB |
|
Isolation Resistance |
|
50 MΩ |
| |
Environmental |
|
Operating Temperature |
|
0 °C to +70 °C (-20 ºC to +70 ºC, SDS180), derate linearly from 100% load at +50 °C to 50% load at +70 °C,
for low temperature option add suffix -L:
-40 ºC to +70 ºC, SDS120 and SDS150,
not available for SDS150-M and SDS180
|
|
Cooling |
|
Convection cooled |
|
Operating Humidity |
|
5-95% RH, non-condensing |
|
Storage Temperature |
|
-40 °C to +85 °C |
| |
EMC and Safety |
|
Emissions |
|
EN55022, CISPR22 level B conducted |
|
Harmonic Currents |
|
EN61000-3-2 class A
120 W: EN61000-3-2 class C for loads ≥30%
150 W: EN61000-3-2 class C n/a
180 W: EN61000-3-2 class C for loads ≥50% |
|
Voltage Flicker |
|
EN61000-3-3 |
|
ESD Immunity |
|
EN61000-4-2, level 2 Perf Criteria A |
|
Radiated Immunity |
|
EN61000-4-3, 3 V/m Perf Criteria A |
|
EFT/Burst |
|
EN61000-4-4, level 2 Perf Criteria A
|
|
Surge |
|
EN61000-4-5, installation class 3
Perf Criteria A |
|
Conducted Immunity |
|
EN61000-4-6, level 2 Perf Criteria A
|
|
Dips & Interruptions |
|
EN61000-4-11, 30% 10 ms, 60% 100 ms, >95% 5000 ms, Perf Criteria A, B, B
|
|
Safety Approvals |
|
EN60950-1, UL60950-1, CSA60950-1 per cUL |
| |
|
|
|
|
|
|
Model Number |
Input |
Output |
Power |
|
|
|
|
|
|
|
| |
SDS120 COVER |
|
|
| Stock Check |
| |
SDS120PS03B |
90-260 VAC |
3.3 V/22.0 A |
72 W | Stock Check |
| |
SDS120PD00B |
90-260 VAC |
o/p 1: 3.3 V/15.0 A, o/p 2: 5.0 V/6.0 A |
79.5 W | |
| |
SDS120PT00B |
90-260 VAC |
o/p 1: 3.3 V/15.0 A, o/p 2: 5.0 V/6.0 A, o/p 3: 12.0 V/1.0 A |
91.5 W | Stock Check |
| |
SDS120PT01B |
90-260 VAC |
o/p 1: 3.3 V/15.0 A, o/p 2: 5.0 V/6.0 A, o/p 3: -12.0 V/1.0 A |
91.5 W | |
| |
SDS120PS05B |
90-260 VAC |
5.0 V/22.0 A |
110 W | Stock Check |
| |
SDS120PS07B |
90-260 VAC |
7.0 V/16.42 A |
115 W | |
| |
SDS120PD01B |
90-260 VAC |
o/p 1: 3.3 V/15.0 A, o/p 2: 12.0 V/6.0 A |
120 W | |
| |
SDS120PD02B |
90-260 VAC |
o/p 1: 5.0 V/15.0 A, o/p 2: 12.0 V/6.0 A |
120 W | |
| |
SDS120PD03B |
90-260 VAC |
o/p 1: 5.0 V/15.0 A, o/p 2: 15.0 V/6.0 A |
120 W | |
| |
SDS120PD04B |
90-260 VAC |
o/p 1: 5.0 V/15.0 A, o/p 2: 24.0 V/3.5 A |
120 W | |
| |
SDS120PD05B |
90-260 VAC |
o/p 1: 5.0 V/15.0 A, o/p 2: -24.0 V/2.0 A |
120 W | |
| |
SDS120PD06B |
90-260 VAC |
o/p 1: 28.0 V/3.92 A, o/p 2: 5.0 V/2.0 A |
120 W | |
| |
SDS120PS09B |
90-260 VAC |
9.0 V/13.33 A |
120 W | |
| |
SDS120PS12B |
90-260 VAC |
12.0 V/10.0 A |
120 W | Stock Check |
| |
SDS120PS15B |
90-260 VAC |
15.0 V/8.0 A |
120 W | Stock Check |
| |
SDS120PS18B |
90-260 VAC |
18.0 V/6.66 A |
120 W | |
| |
SDS120PS24B |
90-260 VAC |
24.0 V/5.0 A |
120 W | Stock Check |
| |
SDS120PS28B |
90-260 VAC |
28.0 V/4.28 A |
120 W | |
| |
SDS120PS36B |
90-260 VAC |
36.0 V/3.33 A |
120 W | |
| |
SDS120PS48B |
90-260 VAC |
48.0 V/2.5 A |
120 W | Stock Check |
| |
SDS120PT02B |
90-260 VAC |
o/p 1: 3.3 V/15.0 A, o/p 2: 12.0 V/6.0 A, o/p 3: 5.0 V/0.8 A |
120 W | |
| |
SDS120PT03B |
90-260 VAC |
o/p 1: 3.3 V/15.0 A, o/p 2: 12.0 V/6.0 A, o/p 3: -5.0 V/0.8 A |
120 W | |
| |
SDS120PT04B |
90-260 VAC |
o/p 1: 3.3 V/15.0 A, o/p 2: 12.0 V/6.0 A, o/p 3: -12.0 V/0.8 A |
120 W | |
| |
SDS120PT05B |
90-260 VAC |
o/p 1: 3.3 V/15.0 A, o/p 2: 12.0 V/6.0 A, o/p 3: 12.0 V/0.8 A |
120 W | |
| |
SDS120PT06B |
90-260 VAC |
o/p 1: 5 V/15.0 A, o/p 2: 12.0 V/6.0 A, o/p 3: 5.0 V/0.8 A |
120 W | |
| |
SDS120PT07B |
90-260 VAC |
o/p 1: 5 V/15.0 A, o/p 2: 12.0 V/6.0 A, o/p 3: -5.0 V/0.8 A |
120 W | Stock Check |
| |
SDS120PT08B |
90-260 VAC |
o/p 1: 5 V/15.0 A, o/p 2: 12.0 V/6.0 A, o/p 3: -12.0 V/0.8 A |
120 W | Stock Check |
| |
SDS120PT09B |
90-260 VAC |
o/p 1: 5 V/15.0 A, o/p 2: 12.0 V/6.0 A, o/p 3: 12.0 V/0.8 A |
120 W | |
| |
SDS120PT10B |
90-260 VAC |
o/p 1: 5 V/15.0 A, o/p 2: 15.0 V/6.0 A, o/p 3: -15.0 V/0.8 A |
120 W | Stock Check |
| |
SDS120PT11B |
90-260 VAC |
o/p 1: 5 V/15.0 A, o/p 2: 15.0 V/6.0 A, o/p 3: 15.0 V/0.8 A |
120 W | |
| |
SDS120PT12B |
90-260 VAC |
o/p 1: 5 V/15.0 A, o/p 2: 24.0 V/3.5 A, o/p 3: -24.0 V/0.8 A |
120 W | |
| |
SDS120PT13B |
90-260 VAC |
o/p 1: 5 V/15.0 A, o/p 2: 24.0 V/3.5 A, o/p 3: 24.0 V/0.8 A |
120 W | |
| |
SDS120PT14B |
90-260 VAC |
o/p 1: 5 V/15.0 A, o/p 2: 24.0 V/3.5 A, o/p 3: -12.0 V/0.8 A |
120 W | |
| |
SDS120PT15B |
90-260 VAC |
o/p 1: 5 V/15.0 A, o/p 2: 24.0 V/3.5 A, o/p 3: 12.0 V/0.8 A |
120 W | Stock Check |
| |
SDS120PT16B |
90-260 VAC |
o/p 1: 5 V/15.0 A, o/p 2: 10.0 V/6.0 A, o/p 3: -10.0 V/1.0 A |
120 W | |
| |
SDS120PT17B |
90-260 VAC |
o/p 1: 5 V/15.0 A, o/p 2: 10.0 V/6.0 A, o/p 3: 10.0 V/1.0 A |
120 W | |
| |
SDS150PS09B |
90-260 VAC |
9.0 V/16.0 A |
144 W | Stock Check |
| |
SDS150PS12B |
90-260 VAC |
12.0 V/12.5 A |
150 W | Stock Check |
| |
SDS150PS12B-M |
90-260 VAC |
12.0 V/12.5 A |
150 W | Stock Check |
| |
SDS150PS15B |
90-260 VAC |
15.0 V/10.0 A |
150 W | Stock Check |
| |
SDS150PS18B |
90-260 VAC |
18.0 V/8.33 A |
150 W | Stock Check |
| |
SDS150PS24B |
90-260 VAC |
24.0 V/6.25 A |
150 W | Stock Check |
| |
SDS150PS24B-M |
90-260 VAC |
24.0 V/6.25 A |
150 W | Stock Check |
| |
SDS150PS30B |
90-260 VAC |
30.0 V/5.0 A |
150 W | |
| |
SDS150PS36B |
90-260 VAC |
36.0 V/4.17 A |
150 W | |
| |
SDS150PS48B |
90-260 VAC |
48.0 V/3.13 A |
150 W | Stock Check |
| |
SDS180PS12B |
90-260 VAC |
12.0 V/14.58 A |
180 W | Stock Check |
| |
SDS180PS24B |
90-260 VAC |
24.0 V/7.5 A |
180 W | Stock Check |
| |
SDS180PS48B |
90-260 VAC |
48.0 V/3.75 A |
180 W | Stock Check |
| |
|
|
|
|
|
|
About XP
Sitemap
|
